Four Way Vehicle Rack System: High Density Pallet Storage for Warehouses
Nov 17,2026
We at Suzhou Industrial Park Haote Logistics Equipment make this Four Way Vehicle Rack System for warehouses that need high density pallet storage without a full automated warehouse. The product page describes the rack body, the shuttle, the track, the lift and the control system, and it gives the density, the throughput and the application cases. This article explains how the system works and what a project should confirm before an order.
How the Shuttle Rack Works
A forklift delivers a pallet to the aisle entrance and places it on the rack level. A shuttle then carries the pallet along the internal track to an empty position deeper in the aisle. For outbound, the shuttle brings the selected pallet back to the entrance and the forklift takes it away. The operator never drives a forklift into the storage lane, which is the basis of the density and the safety gain.
The system is made of the rack body, the shuttles, the track, the lifting and conveying equipment and the control system. The page describes the shuttle as the core execution component. It moves forward and backward on the track, positions itself under a pallet and lifts it for transport. The control system receives the task and plans the route.
Density and Throughput
The page says the system reaches a storage density 50 to 80 percent higher than a beam racking system, close to an automated storage and retrieval system. It also says the operational efficiency rises by 30 to 50 percent because the forklift only works at the aisle entrance and the shuttle does the travel inside the lane.
A single shuttle can handle 30 to 50 pallets per hour, including inbound, outbound and relocation. With multiple shuttles, lifts and conveyors, the page gives an overall figure of 80 to 120 pallets per hour. That is higher than a drive-in rack at 20 to 30 pallets per hour and lower than a full AS/RS at 150 to 200 pallets per hour, so the system fits a medium turnover warehouse.
Components and Construction
The uprights are Q235B or Q355B steel with a cross section of 120 by 100 mm and above. The beams are welded beams or I-beams with a deflection of no more than L/250. The rail support beams fix the shuttle track and are integrated with the beams to keep the rail level. Those details decide the load capacity and the smoothness of the shuttle travel.
The shuttle frame is aluminum alloy or steel, the drive is a servo motor with a reducer, and the wheels are polyurethane for wear resistance and low noise. The lifting platform is hydraulic or electric, and the control is a PLC with a wireless module. The track is C-shaped steel or rail, with end limiters and a buffer to prevent a derailment.

Modes and Applications
The system can switch between FIFO and FILO modes. FIFO is used where the oldest stock has to ship first, such as food, beverage and cold chain. FILO is used where the last pallet in is the first one out, which suits a deep lane with a single access point. The buyer should choose the mode with the inventory rule, not with the equipment alone.
The page lists food and beverage and cold chain, pharmaceutical and chemical, manufacturing and e-commerce or third party logistics as the main applications. It notes that the system suits a full pallet flow and a medium turnover, and that it is not the best choice for a high frequency split pick. A warehouse with many small orders should look at a different picking system.
Power, Maintenance and Safety
The mainstream shuttle is battery powered with a lithium battery. The page says a charge lasts 8 to 12 hours and a fast charge restores 80 percent in 2 hours, and the shuttle can return to the charging station by itself. A wired shuttle is also possible on a large project through a sliding contact line.
The page says the maintenance cost is moderate, higher than a traditional rack and lower than a full AS/RS. The main tasks are the battery check every one or two years, the cleaning and lubrication of the wheels and rails, and the software update. It recommends one or two trained maintenance staff or an annual service agreement.
About Haote
Suzhou Industrial Park Haote Logistics Equipment Co., Ltd. is based in Suzhou Park with a production base in Changshu. The company says it has an R and D team for flexible sorting systems and warehouse automation, and its range includes traditional shelving, dynamic storage, shuttle racks, CTU racks and automated storage and retrieval systems.
Next Step
To request a quotation for the Four Way Vehicle Rack System, send the pallet size, the load, the warehouse height, the temperature, the turnover, the FIFO or FILO rule and the destination. We will confirm the rack layout, the shuttle count and the lift and conveyor plan that fit the site. A layout drawing and a throughput estimate can be provided for the project review.